New Approach to Longwall Gate Support - Juniper publishers

Journal of Insights in Mining Science & Technology


Abstract
Present gate support systems are typically only passive in design, and in less than ideal ground conditions, often result in loss of travel-way integrity and longwall productivity as the front abutment passes. Notably, “Mines in the western United States the amount of convergence measured in the mine entry will vary depending on how much load resistance is provided by the support system the lowest required support capacity would be one that is developed just before this critical roof deformation occurs where failure of the immediate roof is fast approaching. However, designing to this lower limit of support capacity leaves no margin of error if load conditions worsen have had limited choices for standing support [1].”
Keywords : Supported roof; Productivity; Control costs; Longwall access gates; Tail gate; Stage loader

 Introduction
Providing specially designed high capacity active supports that advance with the face will provide added safety, added pro­ductivity, and lower roof control costs [2]. Workers will be able to travel from kitchen to unloaded escapeways under actively supported roof (Figure 1). Front abutments extend from a few feet to more than two hundreds of feet into the gates ahead of the longwall face. The extent of the front abutment varies due to the depth of overburden, strength of the coal, and types of over­burden and the propensity to “ride” ahead of the face (Figure 2).


Longwall Access Gates
Abutment - In coal mining,
a. The weight of the rocks above a narrow roadway is transferred to the solid coal along the sides, which act as abutments of the arch of strata spanning the roadway
b. The weight of the rocks over a longwall face is trans­ferred to the front abutment, that is, the solid coal ahead of the face and the back abutment, that is, the settled packs be­hind the face.
Although ground pressures ride out ahead of the longwall face (the front abutment), the critical longwall access gates im­mediately out by from (ahead of) the longwall face historical­ly utilize only passive roof support (roof bolts, cable bolts etc.) combined at times with costly tensioned cable bolts and/or hand-set props that provide some very limited ground control capacity, that can lead to rib failures requiring additional sup port [3]. These limited support systems in the gates unfortu­nately too often lead to entry roof, floor, and rib failures. These failures all too often restrict head gate and tail gate travel for personnel, equipment, and airflow that results in loss of produc­tivity. Also, the failures can result in the temporary loss or near loss of the tailgate escape way and the full airflow path.
The significant advances made in longwall face support ca­pacities, now needs to be extended into the gates with new tech­niques and specialized equipment. The newly designed equip­ment needs to provide:
a) Active: roof, floor, and rib support by applying hydrau­lic or significant mechanical support prior to the arrival of the front abutment in the gate entry. This will make it pos­sible for longwall workers to travel into the face gates com­pletely shielded from the high stresses that form close to the longwall face.
b) Significant: support pressures are needed to provide load bearing capabilities measured in the 100’s of tons and like those presently in use along the longwall face.
c) Self-Advancing: capability to mesh with the self-ad­vancing longwall supports providing for full automation of the longwall system.
d) Integrated: into longwall system to provide added gate passageway safety and incorporating the stage loader.
e) Automation: Automation of the gate support systems are essential for eventual full longwall face automation.
Potential Cost Savings
Operating cost savings can be realized in both roof control costs and productivity increases. Presently, longwall mines in­stall extensive additional roof support in the tailgate entries and to a lesser extent in the headgate (such as added length roof bolts, cable bolts, etc). This additional, primarily passive, sup­port is installed as the previous longwall panel is extracted and for the full length of the tailgate and headgate, at a high sunk cost for materials and labor. However, these added support systems are not fully utilized until the front abutment arrives and rep­resent a sunk cash flow investment. Providing active and substantial supports in these entries that advance with the long­wall face should make it possible to greatly reduce the need for the current added passive support systems. Also, the passive support systems in the beltway and tailgate travel way often are insufficient or less than fully effective. The lack of effective sup­port leads to congested travel ways and slowing or stopping of production at the longwall face to clear equipment or for effi­cient personnel travel. Further, automation of this new advanc­ing gate support system will provide for added safety, decreased labor costs, and decreased supply costs, with a high probability of more than offsetting the capital costs involved. Automation of the gate support systems are essential for eventual full long­ wall face automation. These new longwall gate support concepts are addressed in: Patent US7331735B2: “Apparatus, system, and method for supporting a gate entry underground full extraction mining”. Figure 3 from the patent shows the general location for the active gate support system, labeled 140. Provisional Applica­tion (filed 2018): “This disclosure relates to full extraction un­derground mining and more particularly relates to automated support of gate entries during longwall mining operations.”

To know more about Insights in Mining science & Technology
https://juniperpublishers.com/imst/index.php

To Know More About Open Access Journals Please click on:

Comments

Post a Comment

Popular posts from this blog

On the Topology of State-space, Linear vs. Nonlinear Theories and Dry Friction

Image
  Insights in Mining Science & Technology Juniper Publishers Authored by  Jozsef Verhas Abstract The work reported here aimed to eliminate the gap between static- and sliding friction on the ground of non-equilibrium thermodynamics with dynamic (internal) degrees of freedom introduced into the state space of the system. Here a germ of a thermodynamic theory is sketched without acquiring generality. Here the simplest model is looked for to eliminate the gap between static and kinetic friction. It is not a complete idea at all but may be a guideline for further modeling. The fork where the train of thoughts stops at gives way to several kinds of possibilities, a number of which by the author’s opinion may have their own realm of application. Finally, an accurately accountable model is given that may be assumed friction if we pretend not knowing its origin and the law differs signficantly from the nearly exclusively used Coulomb’s law. This example support...
Read more

Prospective Use RDF-Raw Materials in Agricultural Technologies and Rubble Concrete

  Abstract In St. Petersburg and the adjacent territory of the Leningrad region there are about 250 unauthorized dumps, which are placed, according to very rough estimates, from 500 thousand to 1 million cubic meters of garbage. A distinctive feature of illegal dumps is the high concentration of heavy and rare metals in the garbage. The article discusses the possibility of using aerobic waste composting as a fertilizer for soil and a solid building material, or alternative solid binder, highly abrasive granules. The applied research methods suggest that RDF wastes are commercialized and have the prospect of becoming a separate innovative product. Read More About This Article:  https://scholar.google.com/citations?view_op=view_citation&hl=en&user=LZr9JboAAAAJ&cstart=20&pagesize=80&sortby=pubdate&citation_for_view=LZr9JboAAAAJ:bEWYMUwI8FkC Read More Juniper Publishers Google Scholar Articles:  https://scholar.google.com/citations?user=cQC-apMAAAAJ...
Read more